How to check and repack rear wheel bearings on Hyundai Accent?

Vehicle owners rarely need to service rear wheel bearings before changing their brake shoes yet they should visually inspect these components whenever lifting their vehicle for other reasons. The required tools for completing this job consist of a torque wrench and special grease. After supporting the vehicle with jackstands you must check each wheel by spinning it to detect noise as well as measure rolling resistance and verify freeplay operations. The spindle requires cleaning and grease application when wheel movement becomes noticeable under your hands during the in-and-out motion on the axle. The wheel removal comes first with optional parking brake adjuster disassembly for the repacking procedure. The dust cap must be removed from the drum/hub assembly while models with a castellated spindle nut require straightening of the cotter pin before its removal. Discard the existing pin and use a new one during reinstallation. The spindle nut and washer need removal to gain access for pulling the drum/hub assembly outward and freeing the outer bearing. Use a seal puller or screwdriver to remove the seal from the rear of the drum/hub after you pull the drum/hub off the spindle while documenting the installation orientation. Remove the inner wheel bearing as you cleanse every surface of old grease from the bearings hub along with spindle through solvent application while allowing parts to naturally dry. Check for cracks and heat discoloration and look at wearing on the bearings as well as examine races for damage. Defective components should be taken to a machine shop for new races. Start by filling wheel bearing grease into the bearings while pushing the grease between the rollers and cone and cage from their back face. Then give a thin grease coat to both the spindle along with bearing seats. At each inner bearing race you should apply a small portion of grease before creating a seal by fingering the opening to block any grease escape. Place the grease-loaded inner bearing at the rear of the drum/hub while adding more grease before using a new seal that requires tapping until the hub surface becomes flush. Set the drum/hub assembly on the spindle before inserting the grease-packed outer bearing correctly into position. The adjustment process includes fitting a washer followed by a spindle nut which you should tighten a little before rotating the drum/hub to settle the bearings and eliminate any remaining grease or burrs. The spindle nut should be tightened to 15 ft-lbs before you loosen it until it is effortlessly loose. Set the nut to a tight position and place the dust cap while adding a new pin and ensuring the flat face of one slot does not extend past the other by more than half thickness. Flattened ends of the cotter pins need to be aligned with the nut before carefully cutting away any extra length that remains. Put in the dust cap by gently tapping it and place the wheel onto the drum/hub securing the lug nuts. The final check of bearings can be performed by lowering the vehicle after placing both hands on the tire top and bottom then achieving the correct torque setting on the lug nuts.

Genuine Hyundai Accent Wheel Bearing

Hub Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

27 Wheel Bearings found

View related parts
Hyundai Accent Front Wheel Hub Assembly
Part Number: 51750-1J000
$146.68 MSRP: $206.08
You Save: $59.40 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Front Wheel; Front Hub, Hub
- Position: Front
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2011-2017 Hyundai Accent | DOHC - GDI | Sedan - 4Door 5P, Sedan - 5Door 5P
View related parts
Hyundai Accent Front Wheel Bearing
Part Number: 51720-1C000
$136.00 MSRP: $191.09
You Save: $55.09 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing-Front Wheel Hub; Bearing
- Position: Front
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2011-2017 Hyundai Accent | DOHC - GDI | Sedan - 4Door 5P, Sedan - 5Door 5P
View related parts
Hyundai Accent Front Wheel Bearing
Part Number: 51720-02000
$122.96 MSRP: $172.76
You Save: $49.80 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing-Front Wheel Hub; Bearing, Wheel Bearing
- Position: Front
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2005-2011 Hyundai Accent | High Grade, Middle Grade | DOHC - MPI | 3 Door Sedan, 4 Door Sedan, Sedan - 3Door 5P, Sedan - 4Door 5P
View related parts
Hyundai Accent Front Wheel Hub Assembly
Part Number: 51750-25001
$127.74 MSRP: $179.47
You Save: $51.73 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Front Wheel; Front Hub, Hub, Hub Assembly
- Position: Front
- Replaces: 51750-25000
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 1999-2011 Hyundai Accent | High Grade, Low Grade, Middle Grade | DOHC - MPI | 3 Door Sedan, 4 Door Sedan, Sedan - 3Door 5P, Sedan - 4Door 5P
View related parts
Hyundai Accent Front Wheel Bearing
Part Number: 51720-H9000
$166.25 MSRP: $233.58
You Save: $67.33 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing-Front Wheel Hub; Bearing
- Position: Front
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2018-2022 Hyundai Accent | DOHC - GDI, DOHC - MPI | Sedan - 4Door 5P
View related parts
Hyundai Accent Rear Wheel Hub Assembly
Part Number: 52750-0U000
$348.21 MSRP: $493.52
You Save: $145.31 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Rear Wheel; Hub & Bearing, Hub & Bearing Assembly
- Position: Rear
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2011-2017 Hyundai Accent | DOHC - GDI | Sedan - 4Door 5P, Sedan - 5Door 5P
View related parts
Hyundai Accent Rear Wheel Hub Assembly
Part Number: 52750-1G101
$416.44 MSRP: $590.23
You Save: $173.79 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Rear Wheel; Hub & Bearing, Hub & Bearing Assembly
- Position: Rear
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2006-2011 Hyundai Accent | DOHC - MPI | Sedan - 3Door 5P, Sedan - 4Door 5P
View related parts
Hyundai Accent Front Wheel Bearing
Part Number: 51720-29400
$63.94 MSRP: $88.90
You Save: $24.96 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing-Front Wheel Hub
- Manufacturer Note: IJC
- Position: Front
- Replaces: 51720-29150, 51720-29300, 51720-29100
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 1999-2006 Hyundai Accent | Low Grade, Middle Grade | 3 Door Sedan, 4 Door Sedan
View related parts
Hyundai Accent Rear Wheel Hub Assembly
Part Number: 52710-22000
$193.27 MSRP: $271.06
You Save: $77.79 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Rear Wheel
- Manufacturer Note: SKF(KMC)
- Position: Rear
- Replaced by: 52710-22400
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 1994-1999 Hyundai Accent | High Grade, Low Grade, Middle Grade | 3 Door, 4 Door
View related parts
Hyundai Accent Rear Wheel Hub Assembly
Part Number: 52750-1G001
$223.30 MSRP: $313.18
You Save: $89.88 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Rear Wheel
- Position: Rear
- Replaces: 52750-1G000, 52750-1G500
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2005-2011 Hyundai Accent | High Grade, Middle Grade | DOHC - MPI | 3 Door Sedan, 4 Door Sedan, Sedan - 3Door 5P, Sedan - 4Door 5P
View related parts
Hyundai Accent Front Wheel Hub Assembly
Part Number: 51750-25000
$129.07 MSRP: $179.47
You Save: $50.40 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Front Wheel
- Position: Front
- Replaced by: 51750-25001
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 1999-2006 Hyundai Accent | Low Grade, Middle Grade | 3 Door Sedan, 4 Door Sedan
View related parts
Hyundai Accent Front Wheel Bearing
Part Number: 51720-21100
$42.36 MSRP: $57.90
You Save: $15.54 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing-Front Wheel Hub
- Manufacturer Note: KBC
- Position: Front
- Replaced by: 51720-22000
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 1994-1999 Hyundai Accent | High Grade, Low Grade, Middle Grade | 3 Door, 4 Door
View related parts
Hyundai Accent Front Wheel Hub Assembly
Part Number: 51750-H9000
$146.68 MSRP: $206.08
You Save: $59.40 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Front Wheel; Front Hub, Hub
- Position: Front
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2018-2022 Hyundai Accent | DOHC - GDI, DOHC - MPI | Sedan - 4Door 5P
View related parts
Hyundai Accent Rear Wheel Hub Assembly
Part Number: 52710-22100
$193.27 MSRP: $271.06
You Save: $77.79 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Rear Wheel
- Manufacturer Note: SKF(KMC)
- Position: Rear
- Replaced by: 52710-22500
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 1994-1999 Hyundai Accent | High Grade, Low Grade, Middle Grade | 3 Door, 4 Door
View related parts
Hyundai Accent Rear Wheel Hub Assembly
Part Number: 52710-22200
$193.27 MSRP: $271.06
You Save: $77.79 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Rear Wheel
- Manufacturer Note: KOYO
- Position: Rear
- Replaced by: 52710-22400
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 1994-1999 Hyundai Accent | High Grade, Low Grade, Middle Grade | 3 Door, 4 Door
View related parts
Hyundai Accent Rear Wheel Hub Assembly
Part Number: 52710-22300
$193.27 MSRP: $271.06
You Save: $77.79 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Rear Wheel
- Manufacturer Note: KOYO
- Position: Rear
- Replaced by: 52710-22500
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 1994-1999 Hyundai Accent | High Grade, Low Grade, Middle Grade | 3 Door, 4 Door
View related parts
Hyundai Accent Rear Wheel Hub Assembly
Part Number: 52750-1G100
$211.26 MSRP: $296.29
You Save: $85.03 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Rear Wheel
- Position: Rear
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2005-2011 Hyundai Accent | High Grade | DOHC - MPI | 3 Door Sedan, 4 Door Sedan, Sedan - 3Door 5P, Sedan - 4Door 5P
View related parts
Hyundai Accent Front Wheel Bearing
Part Number: 51720-29300
$63.94 MSRP: $88.90
You Save: $24.96 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing-Front Wheel Hub
- Manufacturer Note: NSK
- Position: Front
- Replaced by: 51720-29400
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 1999-2006 Hyundai Accent | Low Grade, Middle Grade | 3 Door Sedan, 4 Door Sedan
View related parts
Hyundai Accent Front Wheel Bearing
Part Number: 51720-25000
$69.38 MSRP: $96.47
You Save: $27.09 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing-Front Wheel Hub
- Position: Front
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 1999-2006 Hyundai Accent | Low Grade, Middle Grade | 3 Door Sedan, 4 Door Sedan
View related parts
Hyundai Accent Rear Wheel Hub Assembly
Part Number: 52710-25001
$130.08 MSRP: $180.87
You Save: $50.79 (29%)
Product Specifications
- Other Name: Hub Assembly-Rear Wheel
- Position: Rear
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 1999-2006 Hyundai Accent | Low Grade, Middle Grade | 3 Door Sedan, 4 Door Sedan

| Page 1 of 2 |Next >

1-20 of 27 Results

Hyundai Accent Wheel Bearing

If you are looking for affordable high-quality OEM Hyundai Accent Wheel Bearing, then you have come to the prime place. Our website provides a large amount of genuine Hyundai Accent Wheel Bearing at unbeatable prices. All our parts come backed with the manufacturer's warranty.

Hyundai Accent Wheel Bearing Parts Questions & Experts Answers

Rear Wheel Hub Assembly
52710-22300
Q: How to check and repack rear wheel bearings on Hyundai Accent?
A: Vehicle owners rarely need to service rear wheel bearings before changing their brake shoes yet they should visually inspect these components whenever lifting their vehicle for other reasons. The required tools for completing this job consist of a torque wrench and special grease. After supporting the vehicle with jackstands you must check each wheel by spinning it to detect noise as well as measure rolling resistance and verify freeplay operations. The spindle requires cleaning and grease application when wheel movement becomes noticeable under your hands during the in-and-out motion on the axle. The wheel removal comes first with optional parking brake adjuster disassembly for the repacking procedure. The dust cap must be removed from the drum/hub assembly while models with a castellated spindle nut require straightening of the cotter pin before its removal. Discard the existing pin and use a new one during reinstallation. The spindle nut and washer need removal to gain access for pulling the drum/hub assembly outward and freeing the outer bearing. Use a seal puller or screwdriver to remove the seal from the rear of the drum/hub after you pull the drum/hub off the spindle while documenting the installation orientation. Remove the inner wheel bearing as you cleanse every surface of old grease from the bearings hub along with spindle through solvent application while allowing parts to naturally dry. Check for cracks and heat discoloration and look at wearing on the bearings as well as examine races for damage. Defective components should be taken to a machine shop for new races. Start by filling wheel bearing grease into the bearings while pushing the grease between the rollers and cone and cage from their back face. Then give a thin grease coat to both the spindle along with bearing seats. At each inner bearing race you should apply a small portion of grease before creating a seal by fingering the opening to block any grease escape. Place the grease-loaded inner bearing at the rear of the drum/hub while adding more grease before using a new seal that requires tapping until the hub surface becomes flush. Set the drum/hub assembly on the spindle before inserting the grease-packed outer bearing correctly into position. The adjustment process includes fitting a washer followed by a spindle nut which you should tighten a little before rotating the drum/hub to settle the bearings and eliminate any remaining grease or burrs. The spindle nut should be tightened to 15 ft-lbs before you loosen it until it is effortlessly loose. Set the nut to a tight position and place the dust cap while adding a new pin and ensuring the flat face of one slot does not extend past the other by more than half thickness. Flattened ends of the cotter pins need to be aligned with the nut before carefully cutting away any extra length that remains. Put in the dust cap by gently tapping it and place the wheel onto the drum/hub securing the lug nuts. The final check of bearings can be performed by lowering the vehicle after placing both hands on the tire top and bottom then achieving the correct torque setting on the lug nuts.