How to install and adjust a Hood Cable and Hood Latch on Hyundai Santa Fe?

For the installation of the latch, first draw a line around it and then remove the bolts holding the hood latch situated at the back of the car's radiator support and then remove the latch. Pull the carpet out by releasing the hood cable by pulling down the harness of the cable ensuring that it unlocks and pull the cable end found at the bottom of the hood. For installation, do the reverse of the process of removal while making sure that the latch sits in a way that the hood will click into place when closed and the bumpers should be slightly squeezed. Inside the car, the location of this 'lever' is behind the steering wheel, close to the floor. Finally, pull down the cable housing end upward to disconnect it from this lever and fix a piece of thin wire or string to this end of the cable. Pull the hood cable away from the latch, begin by removing the left inner plastic part of the car's bumper, which will expose all cable retaining clips which are found on the car's radiator support alongside the outer fenderwell and after you have removed the left plastic liner, you will be able to access the hood cable. Pull the cable forward into the wheel well until the wire or string is visible, extract it from the old cable and secure it at the new one. Once the new cable is connected, slowly retract the wire or string back through the body making sure that the new cable is enclosed in the handle found inside. Insert the new cable in the hood release lever so that the cable housing fits into the groove of the handle bracket; while pulling the other end from the interior of the car to seat the cable stop into the grommet on the body. Perform several steps that are the reversal of the previous removal procedures.

Genuine Hyundai Santa Fe Hood Latch

Engine Hood Latch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Hood Latches found

View related parts
Hyundai Santa Fe Hood Latch Assembly
Part Number: 81130-2W000
$57.78 MSRP: $81.18
You Save: $23.40 (29%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Latch Assembly-Hood; Latch Assembly, Lock
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2013-2015 Hyundai Santa Fe | DOHC - GDI | Wagon - Long 5Door 6P, Wagon - Long 5Door 7P
View related parts
Hyundai Santa Fe Hood Latch Assembly
Part Number: 81130-2B010
$102.87 MSRP: $144.53
You Save: $41.66 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Latch Assembly-Hood; Latch Assembly, Lock
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2006-2009 Hyundai Santa Fe | High Grade, Middle Grade | DOHC - MPI | 5 Door Wagon, 5 Door Wagon 7, Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Hyundai Santa Fe Hood Latch Assembly
Part Number: 81130-26000
$34.95 MSRP: $48.68
You Save: $13.73 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Latch Assembly-Hood; Latch Assembly, Lock
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2000-2006 Hyundai Santa Fe | High Grade, Middle Grade | 5 Door Wagon
View related parts
Hyundai Santa Fe Hood Latch Assembly
Part Number: 81130-2W001
$56.20 MSRP: $78.27
You Save: $22.07 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Latch Assembly-Hood; Latch Assembly, Lock
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2013-2018 Hyundai Santa Fe | DOHC - GDI | Wagon - Long 5Door 6P, Wagon - Long 5Door 7P
View related parts
Hyundai Santa Fe Hood Latch Assembly
Part Number: 81130-S1000
$125.73 MSRP: $176.65
You Save: $50.92 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Latch Assembly-Hood; Latch Assembly, Lock
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2019-2023 Hyundai Santa Fe | DOHC - GDI, DOHC - TCI/GDI | Wagon - 5Door 5P
View related parts
Hyundai Santa Fe Hood Latch Assembly
Part Number: 81130-2B200
$102.87 MSRP: $144.53
You Save: $41.66 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Latch Assembly-Hood; Latch Assembly, Lock
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2009-2012 Hyundai Santa Fe | DOHC - MPI | Wagon - 5Door 5P
View related parts
Hyundai Santa Fe Hood Latch Assembly
Part Number: 81130-S2000
$109.35 MSRP: $153.63
You Save: $44.28 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Latch Assembly-Hood
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2019-2020 Hyundai Santa Fe | DOHC - GDI, DOHC - TCI/GDI | Wagon - 5Door 5P

Hyundai Santa Fe Hood Latch

Hood Latch secures in place the hood of the Hyundai Santa Fe so that it does not open while traveling and protects the important engine parts from thieves, road debris, and unexpected opening. The main Hyundai Hood Latch setup in Santa Fe integration and this present generation uses an interior handle, release cable, and spring-loaded catch under the grille. In every Hyundai, when the driver engages the cabin lever, the cable slackens and the catch releases. However, there is a secondary hook in place holding the panel in place. This has to be lifted up by hand. So, it is a two-step process rather than one. This is done to prevent the hood from hitting the windshield in case the main catch slips. Subsequent enhancements from Hyundai incorporated latch assemblies constructed from high-grade steel and reinforced plastic housing, enhancing strength while retaining factory specs to make sure every Hood Latch fits without any drilling and resists corrosion. There are security-oriented versions that include a lock cylinder and plate tumbler sidebar. These offer Santa Fe owners more anti-theft security than the standard Hood Latch design, which is spring-only. Whatever the trim, each model is fitted with this tested mechanism that acts as the first line of defense during collisions and holds the medial portion of the panel down so it does not fly up. Further, the dependable feel of the Hood Latch is a small but integral part of the unique Santa Fe driving experience.

If you are looking for affordable high-quality OEM Hyundai Santa Fe Hood Latch, then you have come to the prime place. Our website provides a large amount of genuine Hyundai Santa Fe Hood Latch at unbeatable prices. All our parts come backed with the manufacturer's warranty.

Hyundai Santa Fe Hood Latch Parts Questions & Experts Answers

Hood Latch Assembly
81130-26000
Q: How to install and adjust a Hood Cable and Hood Latch on Hyundai Santa Fe?
A:
For the installation of the latch, first draw a line around it and then remove the bolts holding the hood latch situated at the back of the car's radiator support and then remove the latch. Pull the carpet out by releasing the hood cable by pulling down the harness of the cable ensuring that it unlocks and pull the cable end found at the bottom of the hood. For installation, do the reverse of the process of removal while making sure that the latch sits in a way that the hood will click into place when closed and the bumpers should be slightly squeezed. Inside the car, the location of this 'lever' is behind the steering wheel, close to the floor. Finally, pull down the cable housing end upward to disconnect it from this lever and fix a piece of thin wire or string to this end of the cable. Pull the hood cable away from the latch, begin by removing the left inner plastic part of the car's bumper, which will expose all cable retaining clips which are found on the car's radiator support alongside the outer fenderwell and after you have removed the left plastic liner, you will be able to access the hood cable. Pull the cable forward into the wheel well until the wire or string is visible, extract it from the old cable and secure it at the new one. Once the new cable is connected, slowly retract the wire or string back through the body making sure that the new cable is enclosed in the handle found inside. Insert the new cable in the hood release lever so that the cable housing fits into the groove of the handle bracket; while pulling the other end from the interior of the car to seat the cable stop into the grommet on the body. Perform several steps that are the reversal of the previous removal procedures.